Frequently asked questions on wedi Seats and Benches
Can I install a wedi suspended seat after the tile has been installed?
Yes you can, simply mark where the seat will be installed. It must be installed in a corner and on both wall sides two studs must be present at 16” o.c. or less so the seats mounting brackets can be installed into two studs later. Cut out your tile, and try to not destroy the wedi panel (or another backer panel) below. If needed, reinstall your wedi building panel (or a different backer panel), using wedi joint sealant around the perimeter of the area removed. Make sure the new panel going back is cut tight and cleanly. After installing into the new joint sealant, more sealant needs to be added around the inside perimeter to ensure a proper seal. After 30-45 mins you can install the cleats of the suspended seat. After that use wedi joint sealant to install the suspended corner seat. In this case the tile should be installed with a pitch to offer water a slight run off the seat. (or this is done with the seat and when tile is cut out)
Can I install benches or countertops out of wedi 2” thick panels and do I have to treat the blue foam edge(s) prior to tiling?
Yes, benches and seats and many more installations such as these can be installed without framework needed. These panels can be cut and fitted together, using wedi joint sealant. When a blue , exposed, foam edge remains , such as at the front of a wedi 2” panel used as a countertop, a strip of wedi panel, 2” wide, can be glued to this edge and will restore a cement resin coated “wedi panel surface” prior to setting tile. Any wedi building panel can be used for making such strips. Most easily this is done with wedi 1/8” building panel. The area which is covered by such strip should be cut back while the element is installed so that the strip is flush with the entire surface.
Can I install a seat build from the floor up after the tile been installed?
Yes, use 2“ wedi building panel to install a seat after the installation of tile. Simply dry cut your boards to the desired height and width. Use wedi joint sealant to bond the board to the tiled walls and floor. In addition, install wedi joint sealant around the perimeter using a standard caulk joint size and your finger. This will keep the sealant off of the tile and give you the needed sealed joint around the perimeter as well. Over very smooth tile please use general primer to using wedi joint sealant.
Can I build a floating seat out of 2” board?
Yes, build a floating seat up to 18“ in length on the walls. This can be made using a minimum 2“ thick wedi panel. Two of these panels can be glued to 4“ or thicker if needed. Use wedi joint sealant to bond the panel to the wall, but make sure the joint sealant is spread over the entire contact surface between wedi seat panel and wedi wall. You should use a fine tooth adhesive trowel with minimum 1/8” x 1/4” notches. All seams from seat to wall ( on top of seat and below) shall be sealed over widely ( 1” either side of seam) using wedi joint sealant and a putty knife. Once this sealant has set, use wedi alkali resistant, and self- adhesive, mesh tape over the seams of top of seat to wall prior to tiling.
What‘s the best way to extend the Ligno base?
When building a seat from the floor up, it‘s best to apply standard framing practices. Install vertical support panels ( 2”) against walls, as sides to the seat, and for the front. wedi 2“ wedi building panel is also installed, within the seat construction, every 18“ for support. Include a sloped top ( slope may be fabricated using wedi joint sealant wet shims or by cutting all supports accordingly) . After sealing and reinforcing the seams in the assembly, as well as seams between seat and wall with wedi joint sealant, you may have additional blue foam exposed. Simply key in thinset over these areas or install a wedi panel strip over these using wedi joint sealant. Cutting areas back to have them covered with a strip that is flush with the seat surface should considered when cutting and dry-fitting the seat assembly. A wedi building strip to cover exposed blue foam is definitely needed when the tile in this area will not overlap from the blue foam area onto the cement coated seat area ( such as when working with mosaics). When building floor standing seats or benches in wert areas and over sloped surfaces, the front vertical seat panel will show a gap to the floor surface. This gap shall not be filled with sealant but should be backfilled with thinset mortar for strong support. wedi mesh tape is used in this thinset mortar application for reinforcement. When installing such seats or benches against areas which may be tiled already, or walls made of cement board or EPS panels, or which may, for any other reason(s) potentially allow water to enter the seat ( e.g. from below wall tiles) it must be ensured it will not get stuck in the seat. The mesh and thinset cover over the fron panel gap will allow water to exit. But if the floor were already tiled, and the use of thinset and mesh is not possible, it will be a good measure to drill a few relief holes into the bottom areas of the seat before tiling.
Your contact to wedi
Do you have more questions to our products or company? Please contact us simply by using our contact form.